efficient • fast • affordable

Maytag washer Repair in Austin, Texas

We provide professional Maytag washer repair in Austin, TX and other Maytag home & laundry appliances within the most reasonable prices.

professional Maytag washing machine repair company near you

The Best Price – Quality Maytag washer Repair In Austin

No matter how well your Maytag washing machine is made, it may need to be repaired at some point. Older models tend to need repairs more often than newer versions, but no matter how old or new your Maytag washing machine is, problems with this reliable appliance can significantly disrupt the lives of homeowners. If you notice that your washing machine is out of order, do not worry – you can rely on us providing the most reliable and efficient Maytag washer repair in Austin and in nearby cities, and we will make sure that your washing machine is put into operation as soon as possible.

So if you are looking for a qualified Maytag washer repair in Austin that can fix your washing machine in a matter of minutes, then Hill Country Repairs is the right place to call! Our local certified specialists are always a Call away fix your faulty Maytag washer usually on the same day.

Maytag washer repair near me

Most Common Maytag washing machine problems

  • The washing machine does not turn on – this may be due to problems with the circuit or simply due to the operation of an unbalanced switch due to an unbalanced load.
  • The machine does not drain the water – it may be due to a clogged drainage hose or a malfunction of the water pump, we can solve any problem.
  • There is a strong vibration – usually this is due to the fact that the machine is not aligned, an unbalanced load or incorrectly adjusted leveling feed or gaskets.
  • The agitator does not move – this usually happens when the assembly is worn out, the drive belt is worn out or the gearbox is no longer working.

Advantages of working with Hill Country Repairs

If your Maytag washing machine has started to mess up and is bothering you, disrupting your comfortable life, it’s time to seek help. Our repair technicians are just a few blocks away and are ready to help.

  • Same-day repairs
  • We service all appliances
  • Licensed and experienced technicians
  • 1-year warranty on the labor and parts
  • Affordable pricing

common Maytag washing machines error code

When you turn on the washing machine and it returns this code during the on cycle, it means that a special sensor detects excess foam. Your appliance switches to foam removal mode, pumps clean water into a tub of clean water, then drains it again and discards the washed clothes. However, the described procedure may not get rid of all the foam. In this case, the washer will return this code again. To avoid such a situation, we would advise you to add the right amount of high-quality detergents when you are going to start a new washing cycle.

To fix the problem, remove all clothes or other items from the washing machine. If you are going to start the cleaning cycle, free the machine from any load inside the drum.

To fix this problem, try unplugging the washing appliance from the mains for at least 5 minutes and thus restart the electronics after the power supply is restored. If your device still displays this error code after restoring normal power, it looks like you will want to replace the main electronic control unit.

Start by disconnecting the washing machine from the main mains. Then inspect all the wires and check how firmly they are connected to the drive control unit. If all the connections are in place and reliable, and you don’t see any problems with them, it would be wise to replace your old drive control unit with a new one.

To eliminate this error code, you will have to order and install the corresponding main electronic control unit. However, if you have not replaced the main board, but the code is still returned, there is a high probability that the main electronic control unit has failed and you will have to replace it with a new one.

First, don’t forget to disconnect your device from the main network. After that, inspect the wires connecting the pressure switch and the main electronic control unit. If you see several loose wires, put them back in place. There is a possibility that your electrical harness is faulty. If so, consider replacing it. There is a high probability that there is a suitable wiring harness in your washing machine. In this case, you should replace the faulty water level pressure switch with a new one.

First disconnect the washing machine from the mains. Then inspect the wiring harness leading to the thermistor. If the wires are in good condition, it is necessary to replace the faulty temperature sensor with a new one.

Check if your appliance is disconnected from the mains and inspect the wiring harness leading to the heater. Most likely, the wiring is in order. If so, you will have to deal with a faulty heater, so consider replacing your faulty heater with a new one.

The code is displayed on the display if the main electronic control unit cannot see the door switch being turned on with 3 consecutive door openings. This means that the door switch did not work properly. You can also see the code when the door switch is activated when the door is closed. In this situation, the door lock or switch needs to be replaced.

Disconnect the washing machine from the mains and inspect the door lock unit for possible damage. You may also want to check all electrical connections leading to the lock. It would be nice to check if the garbage is stuck in the door lock block. If you see something that doesn’t relate to the lock assembly, delete it. If you do not see any damage to the wiring and debris in the lock, then the lock block or switch needs to be replaced.

In this case, you will not be able to unlock the washing machine. Disconnect the washer from the main mains and inspect the door lock unit for any damage. You may also want to look for any loose wires leading to the door lock. If the wiring is in good condition, it is necessary to replace the faulty door/lock switch.

Maytag washer repair in Austin

order our Maytag washer repair in Austin services today

If you are searching for “Maytag Washer Repair Near Me” on Google, checking online reviews and requesting recommendations from friends and family are great ways to find a reliable and professional washer repair in Austin, Cedar Park, Georgetown, Lakeway, Pflugerville, Round Rock, Westlake and West Lake Hills in Texas.

We treat every service call with an outlook towards the future. Our ultimate goal is to provide results that meet your expectations and leave you satisfied. If you need a professional Maytag washer repair technician to look at it or any faulty Maytag appliances you have, leave your contact information bellow and we’ll get back to you immediately! You can also call us on 512-230-7132 for rapid deployment of Hill Country Repairs crew. Thank you for choosing Hill Country Repairs for Maytag washer repair in Austin.

Don’t Wait

Contact Us For A Free Consult